Our Services
Decorative and protective concrete systems for residential and commercial properties across Northern California — interior and exterior, prepared mechanically and installed to suit how the space is actually used.
What We Install
Every system below starts with the same mechanical preparation. What changes is the finish, the build and how the surface handles traffic, moisture and sunlight.
A seamless chip-broadcast surface that hides imperfections, shrugs off chemicals, and cleans with a mop.
Full-broadcast vinyl flake locked between epoxy and a clear topcoat, producing a dense, textured floor that wears evenly for years.
Request an Estimate
Hand-worked pigments that move like stone and marble. No two floors are ever the same.
Reflective metallic pigments dispersed and manipulated by hand, then sealed under a clear coat for depth you cannot get from a printed finish.
Request an Estimate
Your existing slab refined through progressive diamond passes into a hard, light-reflective finish.
A mechanically polished surface that densifies the concrete itself rather than adding a coating on top of it.
Request an Estimate
Translucent colour that penetrates the slab, producing variation that lives in the concrete rather than on it.
Acid and water-based stains that react with the slab to create depth, movement and a finish no two pours share.
Request an Estimate
Systems specified for uptime — phased scheduling, controlled dust, and finishes rated for the traffic they take.
Floor systems selected around service life, cure window and operational disruption, for facilities that cannot simply close.
Request an Estimate
The upgrade homeowners notice first — bright, sealed, and genuinely easy to keep clean.
A properly prepared and coated garage slab that resists hot tires, road salt and dropped tools instead of peeling under them.
Request an Estimate
Colored quartz set in resin for a dense, slip-resistant surface built for wet and high-traffic areas.
A troweled or broadcast quartz system offering the highest impact and abrasion resistance in the decorative range.
Request an Estimate
A cost-effective, durable finish that opens the surface, then locks it under a protective sealer.
Mechanical grinding to the desired aggregate exposure, followed by a sealer chosen for the room's traffic and light.
Request an Estimate
Fast-return, UV-stable topcoats that stay clear and stand up to hot tires and direct sun.
A high-solids topcoat that cures quickly across a wide temperature range and resists the ambering that affects standard epoxies outdoors.
Request an Estimate
Custom color, aggregate and finish work for surfaces designed alongside the architecture.
Bespoke decorative work developed from samples, so the floor answers to the room rather than a catalogue.
Request an Estimate
Seamless poured surfaces for kitchens, bars and vanities, finished to a stone-like depth.
Poured and hand-finished countertops with no grout lines and no seams, formed to the exact footprint of the space.
Request an EstimatePlaceholder visuals — real project photography will replace these as it is supplied.
Residential Solutions
A home surface has to survive real use — cars, weather, furniture and foot traffic — while still looking like it belongs. That balance comes from preparing the slab properly and matching the system to the environment it has to sit in.
Systems chosen for how the space is actually used — parked cars, dropped tools, patio furniture, sun and weather.
Seamless, non-porous surfaces mean spills wipe up instead of soaking into bare concrete and staining it permanently.
Color, flake blend and sheen selected from samples first, so the finish suits the house rather than fighting it.
An exposed pool deck and an interior living floor need different products. We specify to the environment, not to a catalog.
Commercial Solutions
Commercial floors are judged on how they hold up and how the space looks while they do it. We scope work around the loads the surface carries, the hours the facility keeps, and how quickly it needs to be back in service.
Forklifts, pallet jacks, foot traffic and rolling loads all wear a floor differently. The system is selected around what the space carries.
A clean, consistent floor is part of how a facility presents itself to customers, tenants and inspectors alike.
Seamless surfaces are quicker to clean and easier to keep looking consistent across a large footprint.
Phasing around business hours, tenant access and other trades so the space keeps operating while work is underway.
Choosing the Right System
The right system depends on where the surface sits and what it has to put up with. These are the factors we work through before recommending anything — and the reason a quote follows a site visit rather than a phone call.
The single biggest fork in the decision. Products that perform indoors are not always the right choice outside.
Direct sun affects how a topcoat holds its color over time, which narrows the sensible options considerably.
Vapor moving up through a slab can undermine a coating from below. Where conditions suggest it, the slab is tested first.
Foot traffic, vehicles and rolling loads each place different demands on thickness and wear resistance.
Solid color, flake, metallic movement, exposed aggregate or translucent stain — the look often narrows the system list on its own.
Wet areas, pool surrounds and kitchens usually call for added texture. It is a design decision made before installation, not after.
How the surface will be cleaned, and how often, is worth deciding up front — it influences both sheen and system choice.
Cracking, previous coatings, spalling and finish quality all shape what is realistic. The slab is assessed before anything is specified.
| System | Often Suited To | Typical Appearance | Worth Knowing |
|---|---|---|---|
| Epoxy | Interior floors, garages, impact-prone areas | Solid color or flake; satin through to high gloss | Builds thickness and helps disguise minor slab imperfections. Generally specified for interiors, since standard epoxies can amber under direct sun. |
| Polyaspartic | Garages, exterior work, fast-turnaround projects | Clear or tinted; satin through to gloss | Cures quickly across a wide temperature range and is commonly chosen as a topcoat where UV stability matters. |
| Epoxy Quartz | Kitchens, wet areas, heavy-traffic commercial | Textured, with colored quartz aggregate | The most heavily built system in the range. The texture that comes with it also adds grip underfoot. |
| Polished Concrete | Retail, showrooms, interior living spaces | Exposed aggregate; matte through to high sheen | Refines the existing slab rather than coating over it, so the result depends on the condition and quality of the concrete underneath. |
| Concrete Stain | Interiors, patios, decorative feature areas | Translucent, mottled and variegated | Color reacts with the slab itself, so no two pours finish identically. Normally sealed once the color is set. |
| Grind & Seal | Cost-conscious interiors, light commercial | Matte through to gloss over exposed aggregate | A straightforward, economical finish. The sealer chosen determines both the sheen and the ongoing maintenance. |
General guidance only — the right specification follows an on-site evaluation of your slab.
Preparation Matters
Coatings rarely fail because of the product. They fail because the slab underneath was never opened up properly. Everything below happens before a single decorative coat is mixed.
Every slab is opened with diamond tooling, not acid-etched. It is the step that decides whether a coating bonds for a decade or lifts in a season.
Profiling, vacuuming and cleaning are handled as their own stage of the job, because a coating can only be as sound as the surface beneath it.
Cracks, spalls and pitting are cut out and filled before any color goes down, so the finished floor reads as one continuous surface.
Slabs are tested where conditions call for it. When vapor is present, a mitigation layer is installed rather than coated over and hoped for.
Grinding is taken to the profile the specified system needs — coarse enough to bond, consistent enough to finish evenly across the whole floor.
Perimeters, door thresholds, control joints and corners are cut in by hand. It is slower, and it is the difference between a coated floor and a finished one.
Service Territory
We evaluate residential, commercial and contractor projects throughout the Northern California territory — from the Sacramento valley through the foothills and north toward Chico. If your project sits near the edge of that map, ask us anyway.
Sacramento · Roseville · Rocklin · Folsom · Elk Grove · Auburn · Lincoln · Chico · Grass Valley · Nevada City and surrounding communities.
Tell us about the space, how it gets used, and what you want it to look like. We will walk the concrete, explain what it needs, and put a clear estimate in writing.